Aluminium Fabrication
Aluminium is the right material for some jobs and the wrong one for others. The difference is environment, load, and what happens to the part once it leaves the workshop. A 4-metre access ladder that has to be hand-carried across a rooftop is a different problem to one that sits in a loading bay. A bracket used outdoors where wood has already rotted once is a different problem to a structural fixing in a dry industrial unit.
We fabricate bespoke aluminium components and structures for commercial, industrial and residential customers. Cat ladders and access platforms, structural brackets, lean-to roof fixings, one-off parts to customer drawings — made in-house using dedicated AC TIG welding plant set up specifically for aluminium. We will also tell you if steel is the better choice for what you need.
Enquire Here
What We Fabricate in Aluminium
- Cat ladders and access platforms where weight or manual handling is a constraint
- Bespoke structural brackets and fixings
- Lean-to roof brackets and architectural elements
- Lightweight structural components for commercial and industrial applications
- One-off and short-run parts fabricated to customer drawings or specification
Aluminium or Steel — How to Choose
Aluminium costs approximately a third more than mild steel as a raw material. That gap closes quickly when you account for what steel needs that aluminium does not.
“It all depends on what environment they’re being used in.”
Steel used outdoors or in damp environments needs surface treatment to prevent corrosion — zinc primer, galvanising, or paint. That adds cost, lead time, and an ongoing maintenance obligation. Aluminium in the same environment can be left in its raw state. No coating required. No rust. The bracket that replaced the rotted wooden ones on an outdoor lean-to was specified in aluminium precisely because the customer had already learned, the hard way, what prolonged outdoor exposure does to the wrong material.
Weight is the other factor. Where something has to be lifted, carried, or positioned by hand — particularly at height or across restricted access — the difference between aluminium and steel can determine whether the job is safely manageable or not. The numbers tell it plainly.
“The ladder was around 25 kilos in weight, but would have been close to 75 in mild steel.”
Three times heavier. On a rooftop with restricted access, that is not a marginal difference — it is the difference between a job that can be done safely and one that cannot.
If the environment is sheltered, load requirements are significant, and weight is not a constraint, mild steel will often be more cost-effective. We will say so.
Welding Aluminium — Why It Requires Specialist Setup
Aluminium cannot be welded using the same process as steel. The material forms a natural oxide layer on its surface — a thin film with a significantly higher melting point than the aluminium beneath it. To weld effectively, that oxide layer has to be broken through first. This requires AC (alternating current) TIG welding, not the DC process used for steel.
We run a water-cooled AC TIG plant dedicated to aluminium work. This is not a general-purpose setup pressed into service when an aluminium job comes in — it is equipment specified and configured for the material. Combined with welders who have trained specifically on the TIG process, it produces clean, structurally sound welds without the porosity and contamination problems that arise when aluminium is approached with the wrong equipment or the wrong technique.
“It requires a skilled operator who’s gone through training.”
A Note on Sections and Sizing — Draw in Imperial
This is the kind of detail that does not appear on any competitor’s website, but it matters on every aluminium job.
Aluminium sections are predominantly supplied in imperial sizes. Customers who draw their requirements in metric — thinking in millimetres, specifying in round metric numbers — can end up with drawings that do not correspond to available stock sections. The result is parts that do not fit together as designed, or material that has to be specially sourced at additional cost and lead time.
“I would always advise a customer to draw in imperial sections — this can cause problems with things fitting together.”
We flag this at the enquiry stage and advise on conversion where needed. It saves time, money, and frustration — and it is the kind of experience that only comes from having worked with aluminium over many years.
How It Works
-
1
Customer contacts us with drawings or a requirement to discuss. The more detail you can provide upfront, the more accurate our initial response.
-
2
Ian advises on material suitability — aluminium vs steel — based on environment, load, weight requirements, and budget. Honest assessment: if steel is the better choice for your job, we will say so.
-
3
Where drawings are provided in metric, we advise on imperial section conversion before proceeding to avoid sizing and fitting problems.
-
4
Grade and section type selected based on application: 6026 T9 for flat bar, 6082 T6 for round bar, 5754 H114 Durbar plate where anti-slip properties are required.
-
5
Material cut, formed, and fabricated using appropriate equipment. Handled carefully throughout to protect raw finishes where no surface treatment is being applied.
-
6
Aluminium welded using AC TIG process with dedicated water-cooled plant. Skilled operators with specific aluminium TIG training.
-
7
Finish discussed and confirmed — raw/mill finish, powder coating (via trusted supplier), or anodising (via trusted supplier).
-
8
Finishing carried out where specified. Completed fabrication delivered or available for collection.
Finishing Options
The right finish depends on the application, the environment, and the budget. Each has genuine trade-offs.
Finish | Best For | Consideration |
Raw / mill finish | Indoor use, sheltered applications, where appearance is secondary, or where anodising is planned later | Scratches easily — very difficult to remove scratches once they occur. Requires careful handling throughout manufacture and installation. |
Powder coating | Improved aesthetics, colour specification, general outdoor use | Can chip under impact over time. Applied by our trusted specialist supplier. |
Anodising | Where both appearance and long-term durability are priorities. Enhanced corrosion resistance, easier to clean, available in colour | Best all-round option for outdoor or high-visibility applications. Applied by our trusted specialist supplier. |
“You have to be very careful with aluminium in its raw state — if you scratch it, it’s very difficult to get those scratches out.”
Where a customer has specified raw finish, we take additional care through the fabrication process to protect the surface. Fixtures, handling, and transit are all considered.
What Makes Advantage Engineering Different
Dedicated aluminium welding setupAC TIG plant with water-cooled torch, configured specifically for aluminium. Not a general-purpose machine pressed into service — specialist equipment operated by trained welders.
Honest material advice
We will tell you if aluminium is the right choice — or if it is not. The conversation starts with environment, load, and budget, not with what makes the sale.
Imperial section knowledgeAluminium sections are predominantly supplied in imperial sizes. We advise customers to draw in imperial from the start, avoiding the fitting problems that arise from metric drawings — a detail that only comes from real experience.
Bespoke to your drawing or spec
Everything is made to order. If it does not exist off a shelf in the size or configuration you need, we can make it. One-off or short run, from customer drawings or a requirement discussed from scratch.
Care with raw finishesRaw aluminium scratches easily and scratches are very difficult to remove. Where no surface treatment is being applied, we take additional care at every stage of manufacture and handling.
Trusted finishing partners
Powder coating and anodising are carried out by vetted specialist suppliers. You get the full finished component back — not a part you have to organise finishing for separately.
A strong set of reviews.
Go look them up
We are so happy with our reviews we have put them on everyp age of this website, direct from Google. Click here to contact us
Project Examples
Cat Ladder — Rooftop Maintenance Access
Challenge: Severely restricted site access — ladder had to be hand-carried across a rooftop
Material: Aluminium (to customer drawings)
Finished weight: approximately 25kg
Steel equivalent weight: approximately 75kg
A client needed a ladder to provide access to a maintenance point on a building. The site access was severely restricted — the ladder had to be carried by hand across a rooftop to reach the installation point. Weight was not a preference, it was a safety constraint.
We fabricated the ladder in aluminium to the client’s own drawings. The finished weight came in at approximately 25kg. The equivalent ladder in mild steel would have weighed approximately 75kg — three times heavier. The aluminium specification made safe manual handling possible. Steel would not have.
“The ladder was around 25 kilos in weight, but would have been close to 75 in mild steel.”
Bespoke Lean-To Roof Brackets — Residential
Quantity: 20 bespoke brackets
Dimensions: 500mm x 300mm on the slope, pre-drilled fixing holes
Material: Aluminium angle
Reason for aluminium: Corrosion and rot resistance — eliminating the same failure mode that had caused the originals to fail
A residential customer needed to replace the brackets on an outdoor lean-to roof. The wooden originals had rotted and failed. Off-the-shelf brackets were not available in the required size.
“He bought 20 of the brackets to replace some wooden brackets that had failed — outdoor use, rotted over time.”
The customer specified aluminium deliberately. Outdoors, exposed to weather, the same conditions that had destroyed the wooden brackets would eventually attack mild steel too without ongoing surface treatment. Aluminium in its raw state does not rot, does not rust, and requires no coating to perform in that environment. We fabricated 20 brackets in aluminium angle, each 500mm by 300mm on the slope, with pre-drilled fixing holes to the customer’s specification. The failure mode that had cost the original installation is gone.
Capabilities
Grades |
6026 T9 (flat bar), 6082 T6 (round bar), 5754 H114 (Durbar plate) |
Thicknesses |
1.5mm up to approximately 25mm (1 inch). Note: many aluminium sections are specified and supplied in imperial sizes. |
Welding process |
AC TIG — required to break through the natural oxide layer on aluminium. Water-cooled plant dedicated to aluminium. |
Welders |
Trained specifically in the AC TIG aluminium welding process |
Finishing — in-house |
Raw / mill finish (natural self-colour). Extra care taken to protect raw surfaces where no coating is specified. |
Finishing — via trusted partners |
Powder coating and anodising — carried out by vetted specialist suppliers and returned as part of the completed job |
Types of work |
Cat ladders and access platforms, structural brackets and fixings, lean-to roof brackets, lightweight structural components, bespoke one-off parts to customer drawings |
Minimum order |
One-off fabrication accepted |
Established |
2005 — 20+ years of fabrication experience |
FAQ’s
-
Aluminium as a raw material costs approximately a third more than mild steel. However, in many applications that premium is offset by what aluminium does not need. Steel used outdoors or in damp environments typically requires zinc primer, galvanising, or paint to prevent rust — adding cost, lead time, and a maintenance commitment. Aluminium in the same environment can be left raw. Depending on the application, the total cost difference is smaller than the material price difference suggests.
-
The key questions are: what environment will it be used in, does weight matter, and what does the finish need to do? Aluminium is the right choice where corrosion resistance is needed without a surface coating, where manual handling or weight at height is a concern, or where a clean natural finish is important. Mild steel is often the more cost-effective choice where none of those factors apply. We will advise honestly based on your specific situation.
-
It can be. Aluminium sections are predominantly supplied in imperial sizes. Drawings specified in round metric figures often do not correspond to available stock sections, which creates fitting problems or requires specially sourced material. We advise customers to convert to imperial sections from the start. If your drawings are in metric, raise this with us early — it is easier to address before fabrication begins than after.
-
Raw finish is the quickest and most cost-effective option — aluminium’s natural colour, no treatment required. It works well for sheltered or indoor applications where appearance is not critical, but scratches easily and scratches are very difficult to remove once they occur. Powder coating improves appearance significantly, gives a wide colour choice, and suits general outdoor use — though it can chip under heavy impact. Anodising is the best all-round option where both longevity and appearance matter: it enhances corrosion resistance beyond raw aluminium, increases surface durability, and is easier to maintain. We can discuss which suits your application.
-
Yes. We fabricate to customer-supplied drawings. Where those drawings are in metric, we will advise on converting to imperial sections to avoid material sizing issues before we proceed.
-
We handle it as part of the job. Powder coating and anodising are carried out through our trusted specialist suppliers and returned to us before the completed fabrication is delivered or collected. You receive a finished component, not a bare part that needs further work.